As an Amazon Associate I earn from qualifying purchases.
1. Cywhrvzsf #ad
Cywhrvzsf 8S 5A Active Equalizer 6S 7S Balancer Lipo Lifepo4 Lto Lithium Active Battery Energy Transfer Equalization Capacitor #adCywhrvzsf #ad
- Satisfactory service: we provide 24-hour online service, Please email SELLER SUPPORT Not Amazon support, If you encounter any problems, we will give you a perfect solution. Product information:before connecting the equalization board, insulation between the bottom board and the battery connection terminals is required to prevent burnout.
Original design:8s 5a active equalizer using the original ultra-low internal resistance MOS, 2OZ copper thickness PCB.
Product name:8s 5a 6s 7s active equalizer balancer suitable : lithium iron phosphate, Suggest Battery Capacity: 60-300AH, check whether each piece of wiring is correct, Lithium Titanate, NCM Ternary Polymer, Voltage: 1.8
8 v-4. 5v. Capacitance principle: 8s 5a 6s 7s active Equalizer Balancer use the internal energy transfer of the battery to transfer and balance the entire battery pack. Protection switch: 8s 5a balancer equalizer with sleep protection, when the voltage is lower than 3V, it will automatically stop and enter the sleep state to reduce the damage to the battery.
|Part Number||Cywhrvzsf -02|
2. XFYBZN #ad
8S 1.2A Inductive Active Equalizer Balancer Energy Transfer Board Li-ion Lipo Lifepo4 LFP Lithium Battery Balance BMS Balancing Protection PCB #adXFYBZN #ad
- Applicable battery type: ncmli-ion/lfp, if more than 30ah, not support lto; single voltage working range: 2. 0v-4. 5v; static working current: 001ma; suggested battery capacity: below 30AH, pls choice high efficiency flying capacitance equalization, search "B09MS9JPDZ" to purchase.
Balance method: detect that the voltage difference between adjacent batteries is greater than 01v to trigger the start of equalization, and the adjacent battery voltage difference is less than 003v to stop working, the board enters under-voltage protection dormant state.
Note: not recommended to be compatible with low strings, be sure to check whether each battery is wired correctly, and do a good job of insulation. Voltage balance accuracy: 30mv typical value between adjacent voltages; balance current: 01v voltage difference 05a-07a balance current, the maximum balance current is 1.
2a when the voltage difference is above 02v. Before connecting the equalization board, Buyer needs to bear the responsibility instead of returning it. Balance indication: 1 when the equalization light is on, the equalization circuit sleeps; 3The equalization light flashes, it drop cells, the equalization work is turned on; 2The equalization light goes out, or the circuit is faulty.
3. DALY #ad
DALY BMS 16S 48V 100A LiFePO4 PCB Protection Board with Balance Leads Wires 3.2V Battery Protection Module Smart BMS for 18650 Battery Pack 48V with UART #adDALY #ad
- Alarm reminder}: when factors like temperature, current cause Negative Affection to Battery, Voltage, There Will be Alarm Display on Bluetooth Smart BMS APP/ PC Monitoring Program.
Package}-- rated 3. 2v lifepo4 smart bms with smart communication function uart*1+Bluetooth Module *1+UART USB *1+NTC*1+Matching Balance Wire*1+ Instruction Manual*1. Quality guarantee}- iso/ fcc/ rohs/ pse/ ce approved. Shipping time-within 9-14 days from China Dalyelec Manufacturing base normally.
Tracking information available. Parameter real time view}-with smart communication function UART Protocol, All Parameters can be check Via Bluetooth App or UART USB Connection with PC Monitoring Program. Parameters programmable} -- charge and Discharge Protection Current, Voltage, Temperature Can Be Reset in Certain Range. Delivery will be postponed as per National Holidays Regulation.
4. QINIZX #ad
3S 4S 12V 5A Battery Active Equalizer BMS Balancer Lipo Li-ion LFP LiFePO4 Lithium Battery Balance Active Energy Transfer Equalization Module Faster Whole Group Capacitor Balancer PCB #adQINIZX #ad
- This can prevent many products from being discarded and wasted. Note: before connect the balance cable to the balance board, it will short-circuit and burn the board. The quiescent current is about 9ma, and the battery capacity is recommended to be used between 30-200AH/Per Balancer.
Tips: this balancer board is backward compatible by default. With under-voltage sleep protection, only detecting the battery voltage of B1, the equalizer will automatically stop entering the sleep state when the B1 voltage is lower than 2.
7v, and the standby power consumption is less than 01mA. Working voltage: 2. 7v-4. 2v, lithium iron phosphate battery lifepo4. Eg. If it is used for 3s, and do a good job of insulating the bottom of the board and the battery string connection terminals.
Tipswhen buyers have problems, please be sure to take the initiative to contact us, suitable for NCM Ternary polymer lithium battery Li-ion, and trust us have the ability to solve your problems, rather than a direct refund returns. Otherwise, be sure to check whether the connections of each section of the battery pack are correct, the last line B4+ is empty. Working principle: flying capacitor transfer charge transporter, the dormant power-off mode working current is less than 0
5. Beffkkip #ad
Beffkkip 4pcs 2A 5V Charge Discharge Integrated Module 3.7V/4.2V PCB Board Module for 18650 Lithium Battery Charging Boosting Mobile Power Board #adBeffkkip #ad
- If the load is less than 50ma, the output will be automatically turned off after 30 seconds; if the load is greater than 50MA, the output will be automatically turned on. In discharge mode the charging mode key function is invalid, trigger the KEY port once to open the output; continuously trigger the KEY port twice to close the output.
The first time the load is connected, the output is automatically turned on. Lithium battery protection function: over-current, over-temperature, overvoltage, short circuit protection.4
4 in 1 charging + discharging + lithium battery Protection + Battery Level Indicator Module. Allow discharge while charging. Trigger mode: low level trigger ground. Note: at this time output voltage 4. 7 / 5v. Mcu users, if you accept a small load key can be connected to the microcontroller about 20s to provide a low level allows the module to continue working.
6. DORHEA #ad
4PCS 6S 6 Series Lithium Battery Level Indicator Capacity Module Lead-Acid Ni-MH 25.2V 4 Sections Blue LED Display Electric Vehicle Battery Power Tester Li-po Li-ion #adDORHEA #ad
- The different electricity quantity will illuminate corresponding blocks electricity quantity. Do not exceed a voltage of 4. 3*n at most. For example, the maximum voltage detected by the module should not exceed 4. 3*3=12. 9 v. The 6s battery capacity indicator module can be used to display lithium battery, lead acid battery, and Ni-MH battery.
The digital tube displays the real-time battery power. Note : after connecting a few series of lithium batteries in series, it is necessary to connect tin to the corresponding pads. For example if a 2s battery is measured two batteries are connected in series, a short circuit on the pad corresponding to S2 of the board is required.
Battery capacity indicator. Clear and bright display, outline red, display block Blue. How to use it: connect the positive and negative terminals of the display board to the positive and negative terminals of the battery under test.
Widely applications: can be widely applied to portable mobile equipment, balance car, cleaning machine, electro mobile, measuring equipment etc. Note: the electricity quantity parameter is a reference value, there will be about 2% error range; This model is not waterproof, if the tin on the pad of s3 is selected, the electronic components should be used in a dry environment; The number of corresponding battery strings and use them within the corresponding voltage range.
7. D-FLIFE #ad
JST XH Board Balance Expansion Charger Adapter gor RC 6S LiPo Battery Charge, D-FLIFE 2pcs RC Product JST-XH-2-6S Lipo Battery Charge Balance Board #adD-FLIFE #ad
- Tp/fp connector is on thunder Power And Flight Power Batteries. Apply to most Lipo Battery Chargers. Pack include:2x Battery Charger Balance Board. Works with 2s - 6s batteries With A JST-XH Balance Plug. Jst xh board balance expansion charger Adapter For RC 6S LiPos Battery Charging.
8. MELIFE #ad
3 Pcs MELIFE 6S 15A 24V PCB BMS Battery Protection Board for Li-ion Lithium 18650 Battery Packs Lipo Cell Module #adMELIFE #ad
- Great design: compact size and light weight, disconnect load self-recovery. Widely applications: use for variety of capacities and various shapes 12V/24V lithium batteries, LED light backup power supply, massager battery pack, monitor standby power supply, solar street light battery pack, etc.
High quality: high-accuracy voltage detection circuit, fine workmanship and durable.
Multiple protection: over-discharge protection, overcurrent protection, overcharge protection; Short circuit protection; High charge and discharge current. Mos transistor can control the battery charge and discharge, low standby current consumption. High efficiency: low internal resistance, high power MOS.
9. Acxico #ad
Acxico 1Pcs 2S-6S Lithium Lipo Battery XT60 Plug to USB 5V Charger Converter Module Adapter #adAcxico #ad
- Also compatible with: any other custom application you can dream up! Support 2s-6s lithium battery, output 5V, support mobile phone charging. Thank you so much for your purchasing from our store. Any question, please feel free to contact us.
For: many helicopter Quadcopter Airplane Boat Car Controller. Package included:1pcs 2s-6s lithium lipo battery xt60 plug to usB 5V Charger Converter Module AdapterIf there are any problems with the product, please send us pictures. Tell us more details about this problem.
10. Hyuduo #ad
BMS 6S 15A 22V 24V Protection Board Lithium Battery Charger PCB Protection Board Overcharge/Overdischarge/Overcurrent/Short Circuit Protect for 18650 Li-ion Cell #adHyuduo #ad
- High quality: the board is made of high quality electronic components and it is stable and reliable. Long service life: this protection board has a long service life and can protect you for a long time. Scope of application; the protection board is suitable for 6 series 3.
7v 18650 lithium ion battery. Device security:lithium protection board provides ultimate protection for your device, charger and most important devices. Multiple protection: protection board has a combination of over-discharge protection, over-current protection, over-charge protection, and short-circuit protection.